Computed tomography (CT) scanning, also known as, especially in the older literature and textbooks, computerized axial tomography (CAT) scanning, is a diagnostic imaging procedure that uses x-rays to build cross-sectional images ("slices") of the body. Cross-sections are reconstructed from measurements of attenuation coefficients of x-ray beams in the volume of the object studied.
CT is based on the fundamental principle that the density of the tissue passed by the x-ray beam can be measured from the calculation of the attenuation coefficient. Using this principle, CT allows the reconstruction of the density of the body, by two-dimensional section perpendicular to the axis of the acquisition system.
The CT x-ray tube (typically with energy levels between 20 and 150 keV), emits N photons (monochromatic) per unit of time. The emitted x-rays form a beam which passes through the layer of biological material of thickness delta x. A detector placed at the exit of the sample, measures N + deltaN photons, delta N smaller than 0. Attenuation values of the x-ray beam are recorded and data used to build a 3D representation of the scanned object/tissue.
In the particular case of the CT, the emitter of x-rays rotates around the patient and the detector, placed in diametrically opposite side, picks up the image of a body section (beam and detector move in synchrony).
Unlike x-ray radiography, the detectors of the CT scanner do not produce an image. They measure the transmission of a thin beam (1-10 mm) of x-rays through a full scan of the body. The image of that section is taken from different angles, and this allows to retrieve the information on the depth (in the third dimension).
In order to obtain tomographic images of the patient from the data in "raw" scan, the computer uses complex mathematical algorithms for image reconstruction.
If the x-ray at the exit of the tube is made monochromatic or quasi-monochromatic with the proper filter, one can calculate the attenuation coefficient corresponding to the volume of irradiated tissue by the application of the general formula of absorption of the x-rays in the field (see Figure 1).
The outgoing intensity I(x) of the beam of photons measured will depend on the location. In fact, I(x) is smaller where the body is more radio-opaque.
Hounsfield chose a scale that affects the four basic densities, with the following values:
- air = -1000
- fat = -60 to -120
- water = 0
- compact bone = +1000
The image of the section of the object irradiated by the x-ray, is reconstructed from a large number of measurements of attenuation coefficient. It gathers together all the data coming from the elementary volumes of material through the detectors. Using the computer, it presents the elementary surfaces of the reconstructed image from a projection of the data matrix reconstruction, the tone depending on the attenuation coefficients.
In conclusion, a measurement made by a detector CT is proportional to the sum of the attenuation coefficients.
The typical CT image is composed of 512 rows, each of 512 pixels, i.e., a square matrix of 512 x 512 = 262144 pixels (one for each voxel). In the process of the image, the value of the attenuated coefficient for each voxel corresponding to these pixel needs to be calculated.
Each image point is surrounded by a halo-shaped star that degrades the contrast and blurs the boundary of the object. To avoid this, the method of filtered back projection is used. The action of the filter function is such that the negative value created is the filtered projection, when projected backwards, is removed, and an image is produced, which is the accurate representation of the original object.
The CT scan deals with the attenuation of the x-rays during the passage through the body segment. However, several features distinguish it from conventional radiology: the image is reconstructed from a large number of measurements of attenuation coefficient.
Before the data are presented on the screen, the conventional rescaling was made into CT numbers, expressed in Hounsfield Units (HU), as mentioned before. CT numbers based on measurements with the EMI scanner invented by Sir Godfrey Hounsfield 6, a Nobel prize winner for his work in 1979, related the linear attenuation coefficient of a localized region with the attenuation coefficient of water, the multiplication factor of 1000 is used for CT number integers.
So, the signal transmitted by the detector is processed by the PC in the form of the digital information, the CT image reconstruction.
- 1. Goldman LW. Principles of CT: Multislice CT. Journal of Nuclear Medicine Technology. Vol. 36, No.2, 2008
- 2. Lazic J, Sobic V, Cikaric S. et al.Radiologija (Radiology – Unviersity Manual), Medicinska Knjiga, Belgrade 1997
- 3. Sprawls P. The Physical Principles of Medical Imaging, 2nd Ed. 1995, Medical Physics Pub. (Madison, Wis)
- 4. Semnic R. CT Toraksa i Abdomena, Institut za Onkologiju Vojvodine, Sremska Kamenica, Grpah Style, Novi Sad 2005
- 5. Stankovic JB, Milosevic NT. Osnovi radioloske fizike (Basic Principles of Radiological Physics), PTT, Belgrade, 2007
- 6. Thomas AMK, Banerjee AK, Busch U. Classic Papers in Modern Diagnostic Radiology. (2004) ISBN: 9783540219279
Related Radiopaedia articles
Physics and imaging technology: CT
computed tomography (CT)
- CT technology
- dual energy CT
- CT image reconstruction
- CT image quality
- CT dose
CT contrast medium
- iodinated contrast media
- coronary CT angiography
- patient-based artifacts
- physics-based artifacts
- hardware-based artifacts
- CT safety
- history of CT